Products

Post it to Twitter Post it to Facebook

EPM 7100 

Model: EPM 7100

Name: Power Quality Meter

Description:

  • Designed for factory and building automation
  • Modbus® RTU protocol
  • Maximum 580V
  • True RMS conversion
  • LCD display

Overview

  •  About Power Meter EPM 7100

EPM 7100 power quality meters are conceptualized to revolutionize the traditional power metering industry. Each power quality meter is a compact, electronically advanced and programmable multi-display metering device (MDMD). It is the solution to the new electrical generation.

  • PLC Modbus(R) Compatible

The Modbus(R) communications protocol allows information and data to be efficiently transferred between EPM 7100 and Modicon programmable logic controller (PLC) or other third party Modbus(R) compatible monitoring and control systems. The EPM 7100 can also establish a monitoring system by simply adopting IPC-based centralized master display software. The RTU mode Modbus(R) protocol with default to baud rate 9600 bps, 8 data bit.

  • Increase Productivity & Efficiency

The EPM 7100 models are specifically designed to be compatible with the most widely used DIN standard panel with DIN 92 * 44mm panel cutout holes. It is also a standardize hardware suitable for various wiring set ups including 1 phase 2 wires, 1 phase 3 wires, 3 phase 3 wires or 3 phase 4 wires networks.

  • Improved Technical Superiority and Reliability

These power quality meters are endowed with technical specifications (overload capabilities, accuracy levels, long term stability, readout dependability etc.) far exceeding conventional instruments. The software provides a simple yet practical solution to energy management in factories and plant, small industries, building services, etc.

  • Factory & Building Automation ( FA & BA )

EPM 7100 was developed for factory and building automation (FA & BA) applications. EPM 7100 allows more power and energy parameters to easily apply to a wide range of AC switch-gear or power distribution system for metering.

  • Field Programmability

The field programmable power meter is able to set e.g. CT and PT ration, Modbus(R) address, communication baud rate, meter's display, etc. either through rear RS-485 communication port or a maintenance port on the front panel with a communication module RX-024 specifically produced by HCE.

  • Comprehensive System Integration

With PLC compatible RS-485 / RS-232 (Option) Modbus(R) communication protocol, the 7000 series allows information and data to be efficiently transferred between power quality meter EPM 7100 RTU, Power SCADA system, and DCS system.

 

Features

  • Designed for factory and building automation
  • Modbus® RTU protocol
  • Maximum 580V
  • True RMS conversion
  • LCD display
  • Field programmable PT / CT ratio
  • Accuracy up to 0.2%
  • Memory for all setup and energy data
  • Comprehensive self test diagnostics
  • Low input burden 0.2VA (5A/120V)
  • Wide power supply range 80~260V AC / DC
  • Compact physical configuration
  • Compatible for DIN&ANSI cutout
  • 2KV RMS input / power isolation

 

Model & Ordering

Specifications

Programmable measurements / Accuracy / Display readouts

     

 

  • Input
    • Range
      • Voltage : 10 ~ 580V
      • Current : Suitable for CT secondary rating (option)
      • Maximum 6A for 5A rating
      • Maximum 1.2A for 1A rating
      • Frequency : 40 ~ 70Hz
    • Burden
    • Voltage < 0.5VA at 580V
    • Current < 0.2VA at rating
    • Overload rating

      

  • Measured system
    • Suitable for 3 phase 4 wires / 3 phase 3 wires
    • Selectable input wiring & software configuration
  • Programmability
  • Communication accessible / password lock (for communication)
  • System selection : 3 phase 4 wires / 3 phase 3 wires
  • PT : 1 - 5000.0 ; CT : 1-5000.0
  • Readout display control 4 digits / auto scan
  • Communication Baud rate 1200 / 2400 / 4800 / 9600 / 19200, Address setting 1 - 254
  • Memory : all of energy date and status setting
  • RS-485
  • MODBUS(R) RTU protocol
  • Communication port
  • IEC 255-5
  • 2KV AC rms 1 minute between input / power
  • ANSI / IEEE C37.90.1-1989 (3KV) SWC test
  • IEC 255-22-1 class III SWC test
  • IEC 255-22-4 class IV (IEC 801-4) SWC test
  • IEC 255-5 1.2 * 50us (4KV) impulse test
  • Temperature range -10 to +55oC, maximum 100 ppm/oC
  • Long term stability 0.15% drift maximum per year
  • LCD 0.3" display, 1 rows of "8" digitals
  • Dielectric strength
  • AC 80 ~ 260V, 40 ~ 70 Hz, DC 80 ~ 330V
  • DC 20 ~ 60V
  • Dissipation maximum 2 VA for AC and 1 Watts for DC
  • Panel type mounting
  • Size : 118 * 98 * 48 mm
  • Cut out : 92 * 44 mm
  • Impulse and surge test
  • Stability
  • Operating condition : Temperature range -10 to +60oC, RH 20 ~ 95% non-condensed
  • Storage condition : Temperature range -25 to +70oC, RH 20 - 95% non-condensed
  • Power supply
  • Mounting / Dimension